AOC 917VW Manuel d'utilisateur

917Vw User Manual 1. Preface About This Guide This guide describes the monitor's features, setup, and operation. lnformation in this doc

1 Eco Mode / Up 2 Exit / Left 3 Menu / Right 4 Auto / Down 5 Power on/off OSD Settings • 1) Press the MENU-button ( ) to activate the OSD

5) Eco Mode hot key ( ) : Press the Eco key continuously to select the Eco mode of brightness when there is no OSD ( Eco mode hot key may not be avail

DCC: Dynamic color control ICM: Intelligent color management 1) How to use Color Boost? YCM adjustment: In addition to the basic R

Five color-enhancement settings: To accommodate various display needs, Color Boost also offers 5 different color enhancement modes: Full Enhance, N

Nature Skin: When "Natural Skin" is turned on, the red and yellow colors are enriched automatically, thus presents human skin with more

Sky Blue: When"Sky Blue" is turned on, the color blue is being fine-tuned so that the sky or ocean landscape will look more vivid and in

2) How to use Picture Boost? Users can change the color settings of a self-selected zone on the screen. The size and position of the selected zone

What is DCR? Dynamic Contrast Ratio (DCR) auto adjusts the brightness of the screen so users can see the darker areas of the displayed content in m

DCR Demos: Disclaimer: DCR aftereffects are subject to the resolution and quality of the display content, hence may look different than the above ill

On Enable dynamic contrast ratio mage Setup Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Focus 0-100 Adjust

WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.Some warnings may appear in alternate formats and m

V.position Adjust Frame vertical Position Bright Frame on or off Disable or Enable Bright Frame OSD Setup H.Position 0-100 Adjus

5. Drivers Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Cont

10. Click on 'Finish' button then the 'Close' button. Windows XP 1. Start Windows® XP 2. Click on the 'Start' button

8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:(CD-ROM Drive:\\Lcd\PC\drivers\). 9. Click th

• Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON

Size(Maximum) Optimal preset resolution 1440 x 900 (60 Hz) Highest preset resolution 1440 x 900 (60 Hz) Plug & Play VESA DDC2B/CI Inp

EPA ENERGY STAR ® ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) GmbH has determined that this pr

Pin Assignments Pin Number 15-Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Ground 6 GND-R 7 GND-G 8 GND-B 9

Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TMDS Data 2- 9 TMDS Data 1- 17 TMDS Data 0- 2 TMDS Data 2+ 10 TMDS Data 1

NOTICE : 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to opera

Precautions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, el

cleanser which will cauterize the monitor cabinet. • Dont leak liquid into monitor which will result in the damage of chassis or component. Please unp

NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Attaching the Cables Cable Connecti

1. Power 2. DVI 3. Analog Turn off your computer before performing the procedure below. 1. Connect the power cable to the AC port on the back of the

Attaching Wall Mounting Arm Preparing to Install An Optional Wall Mounting Arm This monitor can be attached to a wall mounting arm you purchase

5. Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall