AOC 931SN Guide de l'utilisateur

- 1 - USER`S GUIDE 931Sn PREFACE………………………………………………………………………..……….2 SAFETY INTRODUCTION…………………………………………………………….3 SETUP………………………………………………………………………………

- 10 - Boost” and “Picture Boost” . DCC: Dynamic color control ICM: Intelligent color management 1) How to use Color Boost? Five c

- 11 - texture. Green Field: When "Green Field" is turned on, the green color is enriched so that football field and mountain land

- 12 - Auto Detect: When “Auto Detect” is turned on, every pigment will be detected and self-adjusted to render a lively picture. Demo:

- 13 - Disclaimer: DCB aftereffects are subject to the resolution and quality of the display content, hence may look different than the above illu

- 14 - DCR Demos: Disclaimer: DCR aftereffects are subject to the resolution and quality of the display content, hence may look different than th

- 15 - Function Control Illustration Luminance Adjust Range Description Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast

- 16 - Color Temp. Warm 6500K Recall Warm Color Temperature from EEPROM. Normal 7300K Recall Normal Color Temperature from EEPROM. Cool 93

- 17 - Reset Reset yes or no Reset the menu to default Exit Exit Exit the main OSD Notes: 1)If the product has only one si

- 18 - Luminance Adjust Range Description Contrast 0-100 Contrast from Digital-register. Brightness 0-100 Backlight Adjustment Eco mo

- 19 - 2. Image setup Image Setup Adjust Range Description Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Phase 0-100

- 2 - PREFACE About This Guide This guide describes the monitor's features, setup, and operation. lnformation in this document is subject to c

- 20 - 3. Color Temperature Color Temp. Adjust Range Description Preset Warm Recall Warm Color Temperature from EEPROM. Normal Recall Norma

- 21 - 4. Color Boost Color Boost Adjust Range Description Full Enhance on or off Disable or Enable Full Enhance Mode Nature Skin on or o

- 22 - 5. Picture Boost Picture Boost Adjust Range Description Bright Frame on or off Disable or Enable Bright Frame Frame Size 14-100

- 23 - 6. Setting 7. Extra

- 24 -

- 25 - 8. Help On this page, you can find the information of the monitor . Welcome to link our website and send email to us if you have any problem

- 26 - DRIVER INSTALLATION GUIDE Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and th

- 27 - 14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box. Windows Vista 1.

- 28 - TECHNICAL SUPPORT Frequently Asked Questions Problem & Question Possible Solutions Power LED Is Not ON  Make sure the power button is O

- 29 - Picture has color defects (white does not look white)  Adjust RGB color or select color temperature Horizontal or vertical disturbances on

- 3 - SAFETY INTRODUCTION FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has

- 30 - Depth 219.7 mm Weight (monitor only) 3.89 kg Weight (with packaging) 5.26 kg Environmental Temperature: Operating 0° to 50° Non-Ope

- 31 - Pin Number 15-Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +

- 4 - LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION

- 5 - SETUP Setup the stand and base Please setup or remove the base following below steps. Adjusting Viewing Angle  For optimal viewing it is r

- 6 - Attaching the Cables Cable Connections On Back of Monitor and Computer 1. Power 3. Analog Turn off your computer before performing the proced

- 7 - This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1.

- 8 - USING THE MONITOR Setting the Optimal Resolution The recommended resolution for this monitor is 1366 by 768. To setup the monitor to this re

- 9 - OSD Settings  Press the MENU-button to activate the OSD window.  Press+ or - to navigate through the functions. Once the desired function